remove all the junk

remove all the junk


clean clean clean

clean clean clean


both sides front and back

both sides front and back


bare metal primer

bare metal primer


I'm partial to using this stainless steel paint from 3M professional

I'm partial to using this stainless steel paint from 3M professional

be sure to carefully mask the roller tracks before painting

be sure to carefully mask the roller tracks before painting


clean the tracks after the frame has been rechromed

clean the tracks after the frame has been rechromed


slide window on frame and install the two stops

slide window on frame and install the two stops


install lower stop all just finger tight

install lower stop all just finger tight


check the smoothness of the window moving up and down... may have to replace the rollers after having the frame rechromed...  but we were luck that ours still functioned smoothly

check the smoothness of the window moving up and down... may have to replace the rollers after having the frame re-chromed... but we were luck that ours still functioned smoothly


backside view of completed quarter windows

backside view of completed quarter windows


Disassemble once again now we know where everything goes...

Disassemble once again now we know where everything goes...


start by making sure your outter felts are installed properly

start by making sure your outter felts are installed properly


After applying some lithium grease to the tracks, carefully slide the guide plate though the window opening

After applying some lithium grease to the tracks, carefully slide the guide plate though the window opening


finger tighten all three bolts with one at the bottom and....

finger tighten all three bolts with one at the bottom and....


two at the top

two at the top


next, and with absolute care, slide the quarter window in through the same slot

next, and with absolute care, slide the quarter window in through the same slot


being sure to have a hand inside to ease the rollers onto the tracks.

being sure to have a hand inside to ease the rollers onto the tracks.


so far so good

so far so good


test slide quarter window up and down along the tracks... make sure there is enough grease for smooth operation

test slide quarter window up and down along the tracks... make sure there is enough grease for smooth operation


Now that the guide and quarter window is in, its  time to jump to the crank mechanism

Now that the guide and quarter window is in, its time to jump to the crank mechanism


remove the roller clips and rollers

remove the roller clips and rollers


clean clean clean

clean clean clean


scrub all that old hard grease and years of crap off of there

scrub all that old hard grease and years of crap off of there


that old worthless grease is like scraping bacon fat off of a broiler tray after it has cooled in the frig...

that old worthless grease is like scraping bacon fat off of a broiler tray after it has cooled in the frig...


wire brush always helps

wire brush always helps


pay special attenton to the roller studs...

pay special attention to the roller studs...


remove ALL rust with emery cloth and then apply a good deal of penetrating oil

remove ALL rust with emery cloth and then apply a good deal of penetrating oil


nice and clean

nice and clean


I clean everything so it is just like brand new... I put this stop on the wire wheel until it shined

I clean everything so it is just like brand new... I put this stop on the wire wheel until it shined


clean or replace all the little parts... nothing like installing newly rebuilt stuff and getting your hands filthy from old grease and filth... then getting it on other parts... clean is best

clean or replace all the little parts... nothing like installing newly rebuilt stuff and getting your hands filthy from old grease and filth... then getting it on other parts... clean is best


bare metal primer where needed,

bare metal primer where needed,


bare metal primer where needed, the rest is roughed up with emery cloth

bare metal primer where needed, the rest is roughed up with emery cloth


I happen to have some hammered bronze paint handy... just need to prevent bare metal from rusting... and this looked kinda cool as well

I happen to have some hammered bronze paint handy... just need to prevent bare metal from rusting... and this looked kinda cool as well


the rest was hit with the stainless steel paint

the rest was hit with the stainless steel paint


another view

another view


clean and dry

clean and dry


ready to install

ready to install


reinstall the return roll up spring... notice the direction of the spring

reinstall the return roll up spring... notice the direction of the spring


crank the regulator so that the arm is pointing down and there is some tention on the spring

crank the regulator so that the arm is pointing down and there is some tention on the spring


new guides

new guides


insert the pins as they will be put into the track then the roller stud on the arm will be pressed into place while rollers are on the track...easier than putting on stud then trying to slip onto track

insert the pins as they will be put into the track then the roller stud on the arm will be pressed into place while rollers are on the track...easier than putting on stud then trying to slip onto track


ready to reinstall (passenger side)

ready to reinstall (passenger side)


adding lithium grease to track

adding lithium grease to track


added the guide roller

added the guide roller


raise the window by had to the highest point

raise the window by had to the highest point


starting with the crank part, insert the crank mechanism up until the lower arms are in the quarter panel

starting with the crank part, insert the crank mechanism up until the lower arms are in the quarter panel


crank the window and hold that arm that connects to the track that is on the frame so that it is close to where it would rest if the window frame track were there

crank the window and hold that arm that connects to the track that is on the frame so that it is close to where it would rest if the window frame track were there


bring the widow down and push the roller stud into the roller that is on the track attached to the quarter window frame

bring the widow down and push the roller stud into the roller that is on the track attached to the quarter window frame


line it up

line it up


snap it in

snap it in


install the additional stop

install the additional stop


using the crank position the other arm near where the other track would be

using the crank position the other arm near where the other track would be


here I installed the roller on the stud... hit the roller with some grease then slinde the track onto the roller

here I installed the roller on the stud... hit the roller with some grease then slinde the track onto the roller


as well as grease the track

as well as grease the track


finger tighten everything

finger tighten everything


crank window up and down to check adjustments

crank window up and down to check adjustments


now its ready to be adjusted once all the other windows and roof rails are installed

now its ready to be adjusted once all the other windows and roof rails are installed


Loading Conversation